# 2014 October 22
#
# The author disclaims copyright to this source code. In place of
# a legal notice, here is a blessing:
#
# May you do good and not evil.
# May you find forgiveness for yourself and forgive others.
# May you share freely, never taking more than you give.
#
#***********************************************************************
#
if {![info exists testdir]} {
set testdir [file join [file dirname [info script]] .. .. test]
}
source $testdir/tester.tcl
set ::testprefix rbucrash
db close
forcedelete test.db-oal rbu.db
sqlite3_shutdown
sqlite3_config_uri 1
reset_db
# Set up a target database and an rbu update database. The target
# db is the usual "test.db", the rbu db is "test.db2".
#
forcedelete test.db2
do_execsql_test 1.0 {
CREATE TABLE t1(a, b, c, PRIMARY KEY(a), UNIQUE(b));
INSERT INTO t1 VALUES(1, 2, 3);
INSERT INTO t1 VALUES(4, 5, 6);
INSERT INTO t1 VALUES(7, 8, 9);
ATTACH 'test.db2' AS rbu;
CREATE TABLE rbu.data_t1(a, b, c, rbu_control);
INSERT INTO data_t1 VALUES(10, 11, 12, 0);
INSERT INTO data_t1 VALUES(13, 14, 15, 0);
INSERT INTO data_t1 VALUES(4, NULL, NULL, 1);
INSERT INTO data_t1 VALUES(1, NULL, 100, '..x');
}
db_save_and_close
# Determine the number of steps in applying the rbu update to the test
# target database created above. Set $::rbu_num_steps accordingly
#
# Check that the same number of steps are required to apply the rbu
# update using many calls to sqlite3rbu_step() on a single rbu handle
# as required to apply it using a series of rbu handles, on each of
# which sqlite3rbu_step() is called once.
#
do_test 1.1 {
db_restore
sqlite3rbu rbu test.db test.db2
breakpoint
set nStep 0
while {[rbu step]=="SQLITE_OK"} { incr nStep }
rbu close
} {SQLITE_DONE}
set rbu_num_steps $nStep
do_test 1.2 {
db_restore
set nStep 0
while {1} {
sqlite3rbu rbu test.db test.db2
rbu step
if {[rbu close]=="SQLITE_DONE"} break
incr nStep
}
set nStep
} $rbu_num_steps
# Run one or more tests using the target (test.db) and rbu (test.db2)
# databases created above. As follows:
#
# 1. This process starts the rbu update and calls sqlite3rbu_step()
# $nPre times. Then closes the rbu update handle.
#
# 2. A second process resumes the rbu update and attempts to call
# sqlite3rbu_step() $nStep times before closing the handle. A
# crash is simulated during each xSync() of file test.db2.
#
# 3. This process attempts to resume the rbu update from whatever
# state it was left in by step (2). Test that it is successful
# in doing so and that the final target database is as expected.
#
# In total (nSync+1) tests are run, where nSync is the number of times
# xSync() is called on test.db2.
#
proc do_rbu_crash_test {tn nPre nStep} {
set script [subst -nocommands {
sqlite3rbu rbu test.db file:test.db2?vfs=crash
set i 0
while {[set i] < $nStep} {
if {[rbu step]!="SQLITE_OK"} break
incr i
}
rbu close
}]
set bDone 0
for {set iDelay 1} {$bDone==0} {incr iDelay} {
forcedelete test.db2 test.db2-journal test.db test.db-oal test.db-wal
db_restore
if {$nPre>0} {
sqlite3rbu rbu test.db file:test.db2
set i 0
for {set i 0} {$i < $nPre} {incr i} {
if {[rbu step]!="SQLITE_OK"} break
}
rbu close
}
set res [
crashsql -file test.db2 -delay $iDelay -tclbody $script -opendb {} {}
]
set bDone 1
if {$res == "1 {child process exited abnormally}"} {
set bDone 0
} elseif {$res != "0 {}"} {
error "unexected catchsql result: $res"
}
sqlite3rbu rbu test.db test.db2
while {[rbu step]=="SQLITE_OK"} {}
rbu close
sqlite3 db test.db
do_execsql_test $tn.delay=$iDelay {
SELECT * FROM t1;
PRAGMA integrity_check;
} {1 2 100 7 8 9 10 11 12 13 14 15 ok}
db close
}
}
for {set nPre 0} {$nPre < $rbu_num_steps} {incr nPre} {
for {set is 1} {$is <= ($rbu_num_steps - $nPre)} {incr is} {
do_rbu_crash_test 2.pre=$nPre.step=$is $nPre $is
}
}
finish_test